若何将CB成立的Activex设定为脚本安全[VC/C++编程]
本文“若何将CB成立的Activex设定为脚本安全[VC/C++编程]”是由七道奇为您精心收集,来源于网络转载,文章版权归文章作者所有,本站不对其观点以及内容做任何评价,请读者自行判断,以下是其具体内容:
深化解析ATL上就有,惋惜我来晚了,昨天刚办理这个问题.
写在这个里面的public,便可以了
class ATL_NO_VTABLE TSignActiveFormXImpl:
VCLCONTROL_IMPL(TSignActiveFormXImpl, SignActiveFormX, TSignActiveFormX, ISignActiveFormX, DIID_ISignActiveFormXEvents)
{
void __fastcall ActivateEvent(TObject *Sender);
void __fastcall ClickEvent(TObject *Sender);
void __fastcall CreateEvent(TObject *Sender);
void __fastcall DblClickEvent(TObject *Sender);
void __fastcall DeactivateEvent(TObject *Sender);
void __fastcall DestroyEvent(TObject *Sender);
void __fastcall KeyPressEvent(TObject *Sender, char &Key);
void __fastcall PaintEvent(TObject *Sender);
public:
void InitializeControl()
{
m_VclCtl->OnActivate = ActivateEvent;
m_VclCtl->OnClick = ClickEvent;
m_VclCtl->OnCreate = CreateEvent;
m_VclCtl->OnDblClick = DblClickEvent;
m_VclCtl->OnDeactivate = DeactivateEvent;
m_VclCtl->OnDestroy = DestroyEvent;
m_VclCtl->OnKeyPress = KeyPressEvent;
m_VclCtl->OnPaint = PaintEvent;
}
// The COM MAP entries declares the interfaces your object exposes (through
// QueryInterface). CComRootObjectEx::InternalQueryInterface only returns
// pointers for interfaces in the COM map. VCL controls exposed as OCXes
// have a minimum set of interfaces defined by the
// VCL_CONTROL_COM_INTERFACE_ENTRIES macro. Add other interfaces supported
// by your object with additional COM_INTERFACE_ENTRY[_xxx] macros.
//
BEGIN_COM_MAP(TSignActiveFormXImpl)
VCL_CONTROL_COM_INTERFACE_ENTRIES(ISignActiveFormX)
END_COM_MAP()
//在这里,看到了吗?
BEGIN_CATEGORY_MAP(CYourComObject)
IMPLEMENTED_CATEGORY(CATID_SafeForScripting)
IMPLEMENTED_CATEGORY(CATID_SafeForInitializing)
END_CATEGORY_MAP()
// The PROPERTY map stores property descriptions, property DISPIDs,
// property page CLSIDs and IDispatch IIDs. You may use use
// IPerPropertyBrowsingImpl, IPersistPropertyBagImpl, IPersistStreamInitImpl,
// and ISpecifyPropertyPageImpl to utilize the information in you property
// map.
//
// NOTE: The BCB Wizard does *NOT* maintain your PROPERTY_MAP table. You must
// add or remove entries manually.
//
BEGIN_PROPERTY_MAP(TSignActiveFormXImpl)
// PROP_PAGE(CLSID_SignActiveFormXPage)
END_PROPERTY_MAP()
/* DECLARE_VCL_CONTROL_PERSISTENCE(CppClass, VclClass) is needed for VCL
* controls to persist via the VCL streaming mechanism and not the ATL mechanism.
* The macro adds static IPersistStreamInit_Load and IPersistStreamInit_Save
* methods to your implementation class, overriding the methods in IPersistStreamImpl.
* This macro must be manually undefined or removed if you port to C++Builder 4.0. */
DECLARE_VCL_CONTROL_PERSISTENCE(TSignActiveFormXImpl, TSignActiveFormX);
// The DECLARE_ACTIVEXCONTROL_REGISTRY macro declares a static 'UpdateRegistry'
// routine which registers the basic information about your control. The
// parameters expected by the macro are the ProgId & the ToolboxBitmap ID of
// your control.
//
DECLARE_ACTIVEXCONTROL_REGISTRY("SignActiveFormProj1.SignActiveFormX", 1);
protected:
STDMETHOD(_set_Font(IFontDisp** Value));
STDMETHOD(get_Active(VARIANT_BOOL* Value));
STDMETHOD(get_AlignDisabled(VARIANT_BOOL* Value));
STDMETHOD(get_AutoScroll(VARIANT_BOOL* Value));
STDMETHOD(get_AutoSize(VARIANT_BOOL* Value));
STDMETHOD(get_AxBorderStyle(TxActiveFormBorderStyle* Value));
STDMETHOD(get_BorderWidth(long* Value));
STDMETHOD(get_Caption(BSTR* Value));
STDMETHOD(get_Color(::OLE_COLOR* Value));
STDMETHOD(get_DoubleBuffered(VARIANT_BOOL* Value));
STDMETHOD(get_DropTarget(VARIANT_BOOL* Value));
STDMETHOD(get_Enabled(VARIANT_BOOL* Value));
STDMETHOD(get_Font(IFontDisp** Value));
STDMETHOD(get_HelpFile(BSTR* Value));
STDMETHOD(get_KeyPreview(VARIANT_BOOL* Value));
STDMETHOD(get_PixelsPerInch(long* Value));
STDMETHOD(get_PrintScale(TxPrintScale* Value));
STDMETHOD(get_Scaled(VARIANT_BOOL* Value));
STDMETHOD(get_Visible(VARIANT_BOOL* Value));
STDMETHOD(get_VisibleDockClientCount(long* Value));
STDMETHOD(set_AutoScroll(VARIANT_BOOL Value));
STDMETHOD(set_AutoSize(VARIANT_BOOL Value));
STDMETHOD(set_AxBorderStyle(TxActiveFormBorderStyle Value));
STDMETHOD(set_BorderWidth(long Value));
STDMETHOD(set_Caption(BSTR Value));
STDMETHOD(set_Color(::OLE_COLOR Value));
STDMETHOD(set_DoubleBuffered(VARIANT_BOOL Value));
STDMETHOD(set_DropTarget(VARIANT_BOOL Value));
STDMETHOD(set_Enabled(VARIANT_BOOL Value));
STDMETHOD(set_Font(IFontDisp* Value));
STDMETHOD(set_HelpFile(BSTR Value));
STDMETHOD(set_KeyPreview(VARIANT_BOOL Value));
STDMETHOD(set_PixelsPerInch(long Value));
STDMETHOD(set_PrintScale(TxPrintScale Value));
STDMETHOD(set_Scaled(VARIANT_BOOL Value));
STDMETHOD(set_Visible(VARIANT_BOOL Value));
STDMETHOD(get_SignStr(BSTR* Value));
STDMETHOD(set_SignStr(BSTR Value));
STDMETHOD(test(BSTR str));
STDMETHOD(test2(BSTR* str));
STDMETHOD(mySign());
STDMETHOD(errorCode(BSTR* errorCode));
};
//---------------------------------------------------------------------------
#endif
以上是“若何将CB成立的Activex设定为脚本安全[VC/C++编程]”的内容,如果你对以上该文章内容感兴趣,你可以看看七道奇为您推荐以下文章:
本文地址: | 与您的QQ/BBS好友分享! |